Parameter/Settings Storage
This page lists where each parameter is stored.
Scene Storage
The following tables show the settings included in the columns and rows of the Store/Recall filter grid. The following information applies to both the Store and Recall filters.
Notes:Scenes are stored in showfiles, so all of the parameters listed below will also be stored within the showfile, including any changes not stored to a scene (e.g. the last EQ setting of a channel will still be stored in the showfile even if it was not stored in the scene before the showfile was saved).
The scope buttons in the Copy menu (EQ, Gate, Aux etc.) follow the same scope as listed below.
Columns
| Column Name | Meaning | Includes Settings |
|---|---|---|
| Input | Input Settings for Channels & Talkback Channels |
Channel Input A/B Selection Analogue Gain Digital Trim Phantom Power On/Off Polarity Flip On/Off Pad On/Off High Gain Sensitivity On/Off Mic Amp High Pass Filter On/Off Net I/O Stagebox Mic/Line Mode Net I/O Stagebox Gain Compensation Point Net I/O Stagebox Limiter In/Out Sum to Mono Balance Talkback Input In/Out |
| Name Eyeconix Colour | Basic Path Details | Path Name Path Eyeconix Image Path Colour |
| Fader | Fader Level | Fader Level |
| Mute | Mute Button Status | Mute On/Off |
| Panning | Panning Settings for All Paths Feeding Multi-Format buses | Pan Left/Right Position Pan Front/Rear Position Width Depth Divergence LFE Gain LFE Only On/Off |
| Inserts | Insert In/Out Statuses | Insert A In/Out Insert B In/Out |
| Filter | Path Filter | Filter In/Out High Pass Filter Frequency Low Pass Filter Frequency High Pass Filter Slope Type Low Pass Filter Slope Type |
| EQ | Path EQ | EQ In/Out Gain (All Bands) Frequency (All Bands) Q (All Bands) Band Type (All Bands) |
| Gate | Path Gate |
Gate In/Out Threshold Range Knee Attack Release Hold External Key In/Out Gate Filters In/Out Peak Mode On/Off Expander Mode On/Off Gate High Pass Filter Frequency Gate Low Pass Filter Frequency |
| Compressor | Path Compressor |
Compressor In/Out Threshold Ratio Knee Attack Release Hold Makeup Gain Auto Makeup Gain On/Off Comp External Key In/Out Comp Filters In/Out Peak Mode On/Off Tube Emulation In/Out Comp High Pass Filter Frequency Comp Low Pass Filter Frequency |
| All Pass Filter | Path All Pass Filter | All Pass Filter In/Out Frequency Q 2nd Order On/Off Polarity Flip On/Off |
| Delay | Path Delay | Delay In/Out Delay Time Units |
| Bus Settings | Extra Settings for Stems, Auxes & Masters | Follow Pan On/Off Follow Mute On/Off Default Feed Point to Bus |
| Stem | Send to Full Stems | Send In/Out Send Gain Send Feed Point Send Panning Left/Right Send Panning Front/Rear Send Panning Width Send Panning Depth Send Panning Divergence Send Panning LFE Gain |
| Aux | Send to Full Auxes | Send In/Out Send Gain Send Feed Point Send Panning Left/Right Send Panning Front/Rear Send Panning Width Send Panning Depth Send Panning Divergence Send Panning LFE Gain |
| Master | Send to Full Masters | Send In/Out Send Feed Point |
| Dry Stem | Send to Dry Stems | Send In/Out Send Gain Send Feed Point Send Panning Left/Right Send Panning Front/Rear Send Panning Width Send Panning Depth Send Panning Divergence Send Panning LFE Gain |
| Dry Aux | Send to Dry Auxes | Send In/Out Send Gain Send Feed Point Send Panning Left/Right Send Panning Front/Rear Send Panning Width Send Panning Depth Send Panning Divergence Send Panning LFE Gain |
| Dry Master | Send to Dry Masters | Send In/Out Send Feed Point |
| Matrix | Settings for the Matrices | Crosspoints In/Out Crosspoints Gain |
| Solo | Global Solo Settings | Solo Bus A Assignment to Solo Channels Solo Bus B Assignment to Solo Channels |
| Output | Direct Output Feed Point for Channels & Talkback Channels | Direct Output Feed Point |
| FX | FX Rack Unit Settings | FX Rack Unit Parameters |
| Display Settings | Brightness Settings | Screen Brightness Surface Brightness Lights Brightness |
| Mute Group Master | On/Off Status of Mute Groups | Mute Groups On/Off |
| VCA Grouping | VCA Assignments | VCA Membership Status |
| Layer & Bank | Bank Called to Each Fader Tile (Does not affect Layer Manager configuration) | Bank Called to Fader Tile 1 Bank Called to Fader Tile 2 Bank Called to Fader Tile 3 Bank Called to Remote Fader Tile 1 Bank Called to Remote Fader Tile 2 |
| External Control | Parameters used to control external devices | Sigma Fader, Solo and Cut L-ISA parameters Spacemap Go parameters Generic OSC device fader and switch parameters |
Rows
| Row Name | Meaning |
|---|---|
| Input Channel | Full Input Channels |
| Stem | Full Stems |
| Aux | Full Auxes |
| Master | Full Masters |
| Dry Input Channel | Dry Input Channels |
| Dry Stem | Dry Stems |
| Dry Aux | Dry Auxes |
| Dry Master | Dry Masters |
| VCA | VCAs |
| OSC Path | OSC Control Paths |
| Matrix Channel | Matrix Output Channels |
| Solo Bus | Solo buses A & B |
| Solo Channel | Solo Output Channels 1-3 |
| Talkback Channel | Talkback Channels 1-2 |
| DAW Channel | DAW Control Channels |
| Rack Slot | FX Rack Units |
| Rack | Rack Names |
| Console | Global Settings |
| Fader Tile | Fader Tiles 1-3 & Remote Fader Tiles 1-2 |
| Local Control Surface | Console Control Surface settings |
| Remote Control Surface | Remote Expander/Remote Console/SOLSA settings |
Showfile Storage
Automation Scenes are stored in showfiles, so all of the settings that are stored in scenes will also be stored in showfiles.
In addition to those settings, the following settings are also stored in showfiles:
| Console Options | External Screen assignment |
|---|---|
| System Options |
Timecode Frame Rate Timecode Input Default Folddown Settings Alternate Folddown Settings Meter Sources |
| Surface Options | All Tile Setup options (Screen Follow Select etc.) All Query Setup options (Compressed/Expanded etc. modes for each path type) All Select/Solo/Q Follow Setup options |
| User Options |
All Solo Setup options (Additive Solo Mode, Default Feed Point etc.) Rehearse Mode On/Off All FFT Analyser options (Enable Analyser, Analyser Follows Selected Path/FX Slot) Lock V-Aux & V-Stem Control from VCAs User Key assignments |
| External Control Options |
IP address and port numbers for all External Devices Generic OSC fader and switch control labels, OSC method addresses, Min & Max values and colours |
| I/O |
BLII/X-Light Port Configuration (BLII Concentrator/BLII Bridge/X-Light Bridge) MADI Port Redundancy Status On/Off Local Analogue I/O Names MADI Stagebox I/O Names MADI Stagebox Gain Sharing On/Off MADI Stagebox Gain Sharing Compensation Point Dante Expander Quantity of Virtual Tie Lines BLII/X-Light Bridge Quantity of Virtual Tie Lines Device Recorder ID Device Rehearse Mode On/Off Global Rehearse Mode On/Off |
| Console Configuration | Number Channels By: Default/Auto-Renumber Quantity of each path type Path formats Input & Output Configuration of Matrices |
| Other |
Selected Path Mute Group Assignments TB to Bus Dim Automation Lock Tile Automation Lock GUI Path Global Recall Safe On/Off (option to store in showfiles) Operating Level DAW Control settings Broadcast Solo Mode Solo Channel Fader Dim On/Off Broadcast Solo Mode Solo Channel Fader Dim Level Broadcast Solo Mode Solo Channel Auto Dim On/Off Broadcast Solo Mode GPI Link from Solo Channel Mute Broadcast Solo Mode GPI Link from Solo Channel Dim |
Console Storage
The following settings are stored in Console Storage. This means they are not stored in scenes or showfiles, and are specific to that individual console.
- Sample Rate
- Clock Source
- Dante Expander Device Name (console end, see Setting Up Dante for more details)
- BLII/X-Light Bridge Device Name (console end)
- All settings for Connectivity and Dante Control networks (DHCP/Fixed, IP address etc.)
- Remote surface Manual Discovery settings
Not Stored
The following settings are not stored in scene, showfile or console storage. These settings will be reset to their default OFF setting when the console is rebooted or when a new showfile is loaded.
- Path Solo On/Off
- Solo In Place On/Off
- Mute Safe On/Off
- Path Global Recall Safe On/Off (option to store in showfiles)
- Main/Remote Surface mode (defaults to Main)
Useful Links
Automation FiltersShowfiles
Index and Glossary
